by Mike Elliott, Kettle River Canoes
email: artisan@canoeshop.ca

While restoring a 1905 J.H. Rushton Indian Girl canoe, I made new seat frames and wove natural cane (rattan) in a standard 6-stage warp-and-weft pattern. What makes these seats special is the trapezoidal stern seat.  Weaving this seat has a number of unique challenges.

The Rushton seats are made of cherry stock 3/4″ thick and 1¾” wide. The holes are set ½” from the inside edge of the frame and are drilled with a 13/64″ bit. The holes on the top and bottom rails are approximately ¾” centre-to-centre while the holes in the side rails are set at 7/8″ intervals.

In my book, This Old Canoe: How To Restore Your Wood-Canvas Canoe, I describe the full process of preparing the seat frames, preparing the cane and handling the cane during the weaving process.

In last week’s blog article – September 08, 2017, I gave instructions on how to weave the standard 6-stage warp-and-weft pattern used in Rushton canoe seats (as well as many other builders in the USA).

First Stage ̶  Begin by lacing vertical strands into each side portion of the seat.  Anchor one end of the strand in R08 with a caning peg.  Be sure to leave 4″ (10cm) of cane extending out of the bottom of the hole.  Set a vertical strand from R08 to B15.  Lace the strand up through B14 to R04 and anchor the strand with a caning peg.  Again, be sure to leave 4″ (10cm) of cane out of the bottom of the hole.

Next, anchor a new strand at T10 and create a set of vertical strands  ̶  T10-B13, B12-T09, T08-B11, B10-T07, T06-B09, B08-T05, T04-B07, B06-T03, T02-B05, B04-T01. Complete the first stage by running vertical strands from L08 to B02 and from B03 to L04.  Again, be sure to leave 4″ of cane extending out of the bottom of L08 and L04.

Second Stage ̶  Horizontal strands laid on top of the first stage strands.  Once these strands are in, tie off the strands left from the first stage.

Third Stage ̶  Repeat the first stage and set these strands next to the first strands.  As mentioned in the previous blog, this creates the “warp” in the weaving pattern.

Fourth Stage ̶  Weave these strands next to the second stage strands as per the instructions in the previous blog.  This creates the “weft” in the pattern.

Weave through three or four pairs of vertical strands, then pull the entire strand through (firmly but not tight).

Continue until all of the side holes have two strands of cane woven from side to side.

Fifth Stage ̶  Beginning in T10, weave under the vertical pairs and over the horizontal pairs until you reach L11.

Then, weave from L10 to T09 and from T08 to L09.

Skip L08 and weave from L07 to T07, T06 to L06 and L05 to T05.

Continue by weaving from T04 to L03 (skipping L04), L02 to T03 and from T02 to L01.

Starting again at T10, weave over the horizontal pairs and under the vertical pairs until you reach B02 (skipping B01). The next diagonal woven strands in the fifth stage are as follows: B03-R01, R02-B04 and B05-R03.

 

Next, weave from R03 to B06 (two diagonal strands in R03), then: B07-R04, R05-B08, B09-R06, R07-B10, and B11-R07 (two diagonal strands in R07).

 

Continue the pattern as follows: R08-B12, B13-R09, R10-B14 and B15-R11. Skipping some holes in the side rails of the seat frame and doubling up in others, allows the fifth stage weaving to work out evenly through the trapezoidal frame.

Sixth Stage ̶  This stage is the same as the fifth stage except the weaving goes over the vertical pairs and under the horizontal pairs.  Starting at T01, the pattern is: T01-R11, R10-T02, T03-R09, R07-T04 (skipping R08), T05-R06, R05-T06, T07-R03 (skipping R04), R02-T08, T09-R01.

 

Starting again at T01, the pattern is: T01-B15 (skipping B16), B14-L01, L02-B13, B12-L03, L03-B11 (two diagonal strands in L03), B10-L04, L05-B09, B08-L06, L07-B07, B06-L07 (two diagonal strands in L07), L08-B05, B04-L09, L10-B03, B02-L11.

The border cane is set around the frame as usual with couching loops of cane in every second hole. Note that both the top and bottom rails have even numbers of holes. Therefore, I set loops of couching cane in T02, T04, T05, T07 and T09.  In the bottom rail, I couched the cane in B02, B04, B06, B08, B09, B011, B13, and B15.

mockup 02

Complete instructions on seat caning (and much more) are available in my book – This Old Canoe: How To Restore Your Wood Canvas Canoe.
If you live in Canada, CLICK HERE to buy the book.
If you live in the USA, CLICK HERE to buy the book.
If you live in the UK, CLICK HERE to buy the book.
Si vous habitez en France, CLIQUEZ ICI acheter le livre.

If you have read the book, please post a review on Amazon and/or Goodreads and/or any other review site.

Advertisements

by Mike Elliott, Kettle River Canoes
email: artisan@canoeshop.ca

In my book, This Old Canoe: How To Restore Your Wood-Canvas Canoe, I describe how to weave natural cane (rattan) in Chestnut canoe seats.  However, most canoe builders used their own weaving pattern for their canoe seats.

Many of the original canoe builders in the USA (Old Town, Carleton, Rushton, Morris, White  ̶  to name a few) used a standard 6-stage warp-and-weft pattern in their seats. Here are instructions on how to weave this pattern.  For this demonstration, I made new cherry seat frames for a 1905 J.H. Rushton Indian Girl.

In my book, I describe the full process of preparing the seat frames, preparing the cane and handling the cane during the weaving process. Here I will present the basic look of each stage and give details that apply to the warp-and-weft pattern.

First Stage  ̶  Vertical strands

Second Stage  ̶  Horizontal strands strung across the strands of the first stage

Third Stage  ̶  A second set of vertical strands set next to the first set.  These vertical strands create what weavers refer to as the “warp”.  To this point, each set of strands is set on top of the previous set without any weaving.

Fourth Stage  ̶  A second set of horizontal strands woven next to the first set.  In this example, start on the right side rail.  You will notice, moving from right to left, the first horizontal strand passes under the first vertical strand and over the second.  In order to lock all four strands in a woven pattern, the second horizontal strand is woven over the first vertical strand and under the second.  This creates what weavers refer to as the “weft”.  Weave the strand over and under three or four pairs of vertical stands.  Then, pull the entire strand through.  Pull the strand firmly but not tight.  Make sure that the strand is woven with the shiny side up and is free of twists.  This process is hard on the cane.  The tight bends required to weave this stage causes the cane to crack or even break on a regular basis.  Be prepared to redo a strand if it breaks.

Continue weaving small sections of the first strand until you get to the left side rail. Pass the strand down through the hole to the underside and come up through the next hole in the left side rail and hold it in place with a caning peg.  Now, continue the pattern by weaving from left to right.

This process is very slow. As you get more strands woven in the fourth stage of the pattern, use your fingernails to adjust the positions of the various strands until they are arranged more or less evenly.

Fifth stage – Diagonal strand woven under the vertical strands and over the horizontal strands.  In this example, I started in the top right-hand corner and wove the strand under the first set of verticals and over the first set of horizontals.  The pattern continues moving from right to left and from top to bottom.  As with all weaving in these patterns, work in small sections of three or four strands before pulling the entire strand through.  Check your work frequently in order to catch mistakes before you get too far into the pattern.

As you continue this diagonal stage, weave two strands into the corner hole.

Continue the pattern, until you have a complete set of diagonal (/) strands.

Sixth stage – Begin this stage in the empty corner on the transverse rail of the seat.  In this example, it is the top left-hand corner.  Trim the working-end of the cane strand to create a sharp point. This makes weaving easier.  Make sure the shiny side of the strand faces up and start the weaving pattern by going under the diagonal strand next to the corner hole on the transverse rail of the seat.  Then, weave over the first set of vertical strands in the pattern and under the first horizontal strands.  Continue in this way (over the second set of vertical strands and under the second horizontal strands) until you reach the opposite transverse rail.

Continue with this pattern for each diagonal (\) strand .

The final step in the seat weaving is to do the usual “couching” to cover the holes in the seat frame. The couching is held in place with loops of cane in every second hole around the seat frame.

mockup 02

Complete instructions on seat caning (and much more) are available in my book – This Old Canoe: How To Restore Your Wood Canvas Canoe.
If you live in Canada, CLICK HERE to buy the book.
If you live in the USA, CLICK HERE to buy the book.
If you live in the UK, CLICK HERE to buy the book.
Si vous habitez en France, CLIQUEZ ICI acheter le livre.

If you have read the book, please post a review on Amazon and/or Goodreads and/or any other review site.

by Mike Elliott, Kettle River Canoes
email: artisan@canoeshop.ca

In my book, This Old Canoe: How To Restore Your Wood-Canvas Canoe, I describe how to weave natural cane (rattan) in Chestnut canoe seats.  However, most canoe builders used their own weaving pattern for their canoe seats.

The Peterborough Canoe Company (1879 – 1961) installed hand-woven cane seats in many of their wood-canvas canoes as well as many of their all-wood canoes. Their pattern is similar to the six-stage “quick” pattern used by the Chestnut Canoe Company (1897 – 1978).  Only the sixth stage in the pattern is different.  In the Chestnut pattern, both diagonal weaving stages (fifth and sixth stages) weave under the vertical strands and over the horizontal strands.  In the Peterborough pattern, the sixth stage weaves over the vertical strands and under the horizontal strands.

In my book, I describe the full process of preparing the seat frames, preparing the cane and handling the cane during the weaving process. Here I will present the basic look of each stage and give details for the sixth stage only for the Peterborough pattern.

First Stage  ̶  Vertical strands

Second Stage  ̶  Vertical strands arranged beside the strands of the first stage

Third Stage  ̶  Horizontal strands

Fourth Stage  ̶  Horizontal strands arranged beside the strands of the third stage

Fifth stage – Diagonal strand woven under the vertical strands and over the horizontal strands

Sixth stage – Begin the pattern in the empty corner on the transverse rail of the seat.  Feed one end of the cane strand through the corner hole from the top-side to the under-side.  Secure the strand-end in the usual manner.  Secure the strand in the corner hole with a caning peg on the top-side.

Trim the working-end of the cane strand to create a sharp point. This makes weaving easier.  Make sure the shiny side of the strand faces up and start the weaving pattern by going under the diagonal strand next to the corner hole on the transverse rail of the seat.  Then, weave over the first set of vertical strands in the pattern and under the first horizontal strands.  Continue in the way (over the second set of vertical strands and under the second horizontal strands) until you reach the opposite transverse rail.

Make sure you weave under the diagonal strand on the transverse rail before threading the strand down through the hole. Pull the strand snug (but not tight) and secure the strand with a caning peg.

Continue with this pattern for each diagonal strand as you work toward the empty corner in the bottom transverse rail of the seat frame. As usual, the corner hole has two strands since it is both a hole along the transverse rail and the side rail.  The strand going into the corner hole as part of the transverse rail strands weaves under the final diagonal strand before entering the hole.  The second strand from the corner hole begins by weaving over the diagonal strand, then under the first set of horizontal strands and over the first set of vertical strands.  Continue in the way until you reach the top transverse rail of the seat frame.

I rarely weave the Peterborough pattern.  Consequently, I have to check and re-check my work constantly.  Work slowly and carefully to ensure you make your mistakes as quickly as possible.

Complete the sixth weaving stage at the corners of the seat. Make sure the strand weaves under the diagonal strand from the transverse rail and over the diagonal strand from the side rail.

Complete the seat weaving with the usual “couching” to cover the holes in the seat frame. The couching is held in place with loops of cane in every second hole around the seat frame.

mockup 02

Complete instructions on seat caning (and much more) are available in my book – This Old Canoe: How To Restore Your Wood Canvas Canoe.
If you live in Canada, CLICK HERE to buy the book.
If you live in the USA, CLICK HERE to buy the book.
If you live in the UK, CLICK HERE to buy the book.
Si vous habitez en France, CLIQUEZ ICI acheter le livre.

If you have read the book, please post a review on Amazon and/or Goodreads and/or any other review site.