by Mike Elliott, Kettle River Canoes
email: artisan@canoeshop.ca

In my book, This Old Canoe: How To Restore Your Wood-Canvas Canoe, I describe how to weave natural cane (rattan) in Chestnut canoe seats.  However, most canoe builders used their own weaving pattern for their canoe seats.

Many of the original canoe builders in the USA (Old Town, Carleton, Rushton, Morris, White  ̶  to name a few) used a standard 6-stage warp-and-weft pattern in their seats. Here are instructions on how to weave this pattern.  For this demonstration, I made new cherry seat frames for a 1905 J.H. Rushton Indian Girl.

In my book, I describe the full process of preparing the seat frames, preparing the cane and handling the cane during the weaving process. Here I will present the basic look of each stage and give details that apply to the warp-and-weft pattern.

First Stage  ̶  Vertical strands

Second Stage  ̶  Horizontal strands strung across the strands of the first stage

Third Stage  ̶  A second set of vertical strands set next to the first set.  These vertical strands create what weavers refer to as the “warp”.  To this point, each set of strands is set on top of the previous set without any weaving.

Fourth Stage  ̶  A second set of horizontal strands woven next to the first set.  In this example, start on the right side rail.  You will notice, moving from right to left, the first horizontal strand passes under the first vertical strand and over the second.  In order to lock all four strands in a woven pattern, the second horizontal strand is woven over the first vertical strand and under the second.  This creates what weavers refer to as the “weft”.  Weave the strand over and under three or four pairs of vertical stands.  Then, pull the entire strand through.  Pull the strand firmly but not tight.  Make sure that the strand is woven with the shiny side up and is free of twists.  This process is hard on the cane.  The tight bends required to weave this stage causes the cane to crack or even break on a regular basis.  Be prepared to redo a strand if it breaks.

Continue weaving small sections of the first strand until you get to the left side rail. Pass the strand down through the hole to the underside and come up through the next hole in the left side rail and hold it in place with a caning peg.  Now, continue the pattern by weaving from left to right.

This process is very slow. As you get more strands woven in the fourth stage of the pattern, use your fingernails to adjust the positions of the various strands until they are arranged more or less evenly.

Fifth stage – Diagonal strand woven under the vertical strands and over the horizontal strands.  In this example, I started in the top right-hand corner and wove the strand under the first set of verticals and over the first set of horizontals.  The pattern continues moving from right to left and from top to bottom.  As with all weaving in these patterns, work in small sections of three or four strands before pulling the entire strand through.  Check your work frequently in order to catch mistakes before you get too far into the pattern.

As you continue this diagonal stage, weave two strands into the corner hole.

Continue the pattern, until you have a complete set of diagonal (/) strands.

Sixth stage – Begin this stage in the empty corner on the transverse rail of the seat.  In this example, it is the top left-hand corner.  Trim the working-end of the cane strand to create a sharp point. This makes weaving easier.  Make sure the shiny side of the strand faces up and start the weaving pattern by going under the diagonal strand next to the corner hole on the transverse rail of the seat.  Then, weave over the first set of vertical strands in the pattern and under the first horizontal strands.  Continue in this way (over the second set of vertical strands and under the second horizontal strands) until you reach the opposite transverse rail.

Continue with this pattern for each diagonal (\) strand .

The final step in the seat weaving is to do the usual “couching” to cover the holes in the seat frame. The couching is held in place with loops of cane in every second hole around the seat frame.

mockup 02

Complete instructions on seat caning (and much more) are available in my book – This Old Canoe: How To Restore Your Wood Canvas Canoe.
If you live in Canada, CLICK HERE to buy the book.
If you live in the USA, CLICK HERE to buy the book.
If you live in the UK, CLICK HERE to buy the book.
Si vous habitez en France, CLIQUEZ ICI acheter le livre.

If you have read the book, please post a review on Amazon and/or Goodreads and/or any other review site.

Advertisements

by Mike Elliott, Kettle River Canoes
email: artisan@canoeshop.ca

fancy-canoe-front-cover_sm

In my last blog article, I put out a request for “fancy” old canoes to restore and document as part of my second book  ̶  This Fancy Old Canoe.  That was three weeks ago.  Since then, I have been contacted by a number of people.  Now, several “fancy” canoes are about to come into the shop.  They are:

1) A 16′ Model B, Type 2 B.N. Morris Canoe circa 1913

bn-morris-canoe-framed-deck

This canoe is fitted with 24″ framed decks. It will be restored to its original condition.

2) A 17′ Willits Canoe circa 1939

willits-canoe-1939

Willits canoes were built in Tacoma, Washington from 1906 to 1963. Only one model of Willits canoe was ever produced  ̶  a 17′ canoe with a double-planked hull.  Transverse planks were fitted in the interior while longitudinal planks were attached to the exterior with 7,000 copper tacks.  A thin layer of cotton muslin soaked in pine tar was stretched over the hull and sandwiched between the two layers of planking in order to create a waterproof vessel.  The result was a truly gorgeous canoe that is very similar to those built by Rice Lake Canoe Company near Cobourg, Ontario (circa 1862 to 1920).

3) A 16′ Longitudinal Strip Canoe circa 1930

longitudinal-strip-canoe

This canoe has yet to arrive in the shop, so I do not know which company built it. Several companies (Peterborough, Lakefield, Strickland, English, Canadian and others) in and around Peterborough, Ontario built these all-wood cedar-strip canoes from the late 1800’s until about 1960.

4) An 18′ Old Town Sponson Canoe circa 1965

old-town-canoe-with-sponsons

This canoe belongs to a summer camp and was fitted with sponsons  ̶  floatation chambers attached just below the outwales on both sides of the canoe.  It may also have a sailing rig.

********************************

wide-board-canoe-unrestored

These canoes, along with a 16′ J.R. Rushton Indian Girl Canoe circa 1905 with closed gunwales, comprise most of the “fancy” features that I plan to document in my second book. The one canoe I would like to restore and do not have lined up yet is a Raised-Batten Wide-Board Canoe.

wide-board-canoe-restored-interior

This is one of the first types of ‘carpentered’ canoe ever designed. They were one of the all-wood canoes constructed in the Peterborough region of Ontario starting in the 1860’s.  The hull was constructed by first steam-bending ribs onto a solid wood mould and then attaching four wide basswood planks on each side of the canoe.  Most of these canoes were painted although some were varnished.

wide-board-canoe-restored-bow-detail

If you happen to have one of these canoes and you are able to get it to my shop in Grand Forks, BC, I will restore it for the cost of materials. My main focus is on the opportunity to restore one of these canoes, so the cost to you is entirely negotiable.

mockup 02

Be sure to get your copy of my book – This Old Canoe: How To Restore Your Wood Canvas Canoe.
If you live in Canada, CLICK HERE to buy the book.
If you live in the USA, CLICK HERE to buy the book.
If you live in the UK, CLICK HERE to buy the book.
Si vous habitez en France, CLIQUEZ ICI acheter le livre.

If you have read the book, please post a review on Amazon and/or Goodreads and/or any other review site.