by Mike Elliott, Kettle River Canoes
email: artisan@canoeshop.ca

About a year ago, when I was in the final stages of writing This Old Canoe: How To Restore Your Wood-Canvas Canoe, I was also developing the marketing plan for the book.  Many self-published authors want to get their book into as many retail outlets as possible.  However, my book is written for a very focused niche audience.  I nurtured my audience over a number of years through this blog.  Consequently, the bulk of my marketing campaign was and is through the use of social media and my book is primarily available through on-line sources.  That said, I also hoped that my book would be available in one national retail chain.

this-old-canoe

I first approached Lee Valley Tools in June 2016.  I delivered a promotional package personally to their head office in Ottawa, Ontario.  I was there as part of my book tour.  WoodenBoat magazine had just published a positive review (written by Jerry Stelmok) which I included as part of the package for Lee Valley Tools.  I was hopeful that they would choose my book as part of their retail offerings.  I heard back from them almost immediately to confirm that they had received my package,  They also had a number of technical questions for me concerning availability, shipping, etc.  I was thrilled with such a quick response.  Then, all communication stopped.

lee-valley-tools-carries-this-old-canoe

By the end of November 2016, I had resigned myself to the idea that Lee Valley Tools was not going to carry This Old Canoe.  Then, I got a phone call.  Apparently, it had taken more than five months for Lee Valley to find someone within their organization who had enough knowledge of wood-canvas canoes to provide them with a credible internal review of my book.  They called me to say that the review was “glowing” and they were looking forward to making This Old Canoe available to their customers. Click here to see This Old Canoe available at the Lee Valley Tools on-line store.

lee-valley-store

I will be helping to promote my book with a number of in-store events as well as original articles in the Lee Valley Tools newsletter.  The schedule for these events and articles has yet to be determined.  A few days after the phone call from Lee Valley, I slipped on a patch of black ice and tore my right quadriceps tendon (just above my knee cap).  The surgery to repair the tendon was on December 7, 2016 and I am now working through several months of healing and physiotherapy to get back to full strength and range of motion.  Once I am mobile again, I’ll let you know when and where I will be appearing in Lee Valley Tools stores.

by Mike Elliott, Kettle River Canoes
email: artisan@canoeshop.ca

The blogs I do on the specifications of canoe components for various types of canvas-covered canoes seem to be quite popular.  Apparently, I am the only one out there taking the time to write about this stuff and share it with others on-line.  This time around, I am presenting a restorer’s guide to the Bobs Special from the Chestnut Canoe Company.

Bobs Special 06

This canoe was one of two lightweight pleasure canoes built by Chestnut (the other was an 11’ solo canoe called the Featherweight that weighed about 38 pounds).  Before I talk about the canoe, I’d like to clarify the name.  According to Roger MacGregor in his book When the Chestnut was in Flower, Henry and William Chestnut were real history buffs.  The telegraph code for the 15’ 50-Lb. Special was BOBS and made reference to Lord Roberts, a major figure during the Second Boer War in South Africa. Over the years, as this wide, light-weight canoe became more difficult to keep under the weight limit of 50 lbs. (the average weight was 58 pounds while the carrying capacity was 700 pounds), they changed the name.  I have seen a variety of Chestnut catalogues call it Bob’s Special, Bob Special and Bobs Special.  So, feel free to take your pick.

Grey Owl standing in a Bobs

If you happen to have a Bobs or have been lucky enough to come across one in need of some TLC, you will notice what a sweet little canoe this is.  It paddles like a dream which is surprising for a canoe that is 37” (94 cm) wide.  Its bottom has a shallow-arch that reduces the waterline width when paddled with a light load.  There is a fair amount of rocker in the ends which adds to its maneuverability.  At the same time, it is not difficult to stand up in a Bobs – making it ideal for fly-fishing or general recreational paddling for a less experienced paddler.

Bobs Special 08

One little note here: I am listing all of the dimensions in inches.  I apologize to all of you who are working in metric.  The canoes were built with imperial measurements originally, so I find it easier and more accurate to stick with this measurement scale.

Chestnut Bobs Special Inwale

 

Inwales –The inwale is a length of White Ash or Douglas Fir 15/16” high with the edge grain visible on the top surface.  It is fashioned to fit the tumblehome present on most Chestnut canoes.  Therefore, the top surface is 9/16” wide while the bottom width is 11/16”.  The last 18” or so at each end is tapered down to about ½” wide (top and bottom) along the sides of the decks.  All of the transverse components (centre thwart and seats) are attached to the inwales with 10-24 (3/16”) galvanized steel carriage bolts.  I replace these with 10-24 silicon-bronze carriage bolts.

prebent outwales

The gunwales (both inwales and outwales) are pre-bent about 18” from the ends.  If you are replacing these components, the wood will have to be soaked for 3 days, heated by pouring boiling water over them and bent onto custom-built forms in order to get a proper fit.

Chestnut Bobs Special Outwale

 

Outwales – The outwales are also made of White Ash or Douglas Fir.  Depending on when the canoe was built, the outwales may have a chamfered edge on the bottom of the outside surface.  Water often gets trapped under the outwales and results in rot on the inside surface of the originals because they assembled the canoe first and then applied paint and varnish.  Consequently, the inside surfaces of the outwales are bare wood.  Therefore, I usually end up replacing this component.  Prior to installation, I seal the wood on all surfaces with a couple of coats of spar varnish.  Unlike the original builders, I do all of the painting and varnishing first and then assemble the canoe.

Chestnut Bobs Special Deck

 

Decks – The decks the Bobs Special were made of hardwood – usually maple, white ash or white oak.  Sometimes, they used mahogany to help reduce the overall weight.  By the time you start restoring your canoe, the decks are often rotted along with the stem-tops and inwale-ends.  They are attached to the inwales with six 1¾” #8 bronze wood screws.  As with the outwales, I help prevent future rot by sealing the decks on all surfaces with a couple of coats of spar varnish.  The deck extends about 18” into the canoe from the end.

Chestnut Stem-Top

 

Stem-Top – You will rarely if ever have to replace the entire stem.  However, I rarely see an original stem-top that is not partially or completely rotted away.  Because the top 6” or so of the stem is straight, you can usually make the repair without having to pre-bend the wood to fit the original stem-profile.

Chestnut Bobs Special Keel

 

Keel – The Bob Special had a regular (tapered) keel installed.  Use a piece of hardwood (the original was ash) and taper each end to 3/8” wide.  The overall length is about 13’.  It will accept the brass stem-band which is 3/8” wide.

Chestnut Lightweight Rib

 

Ribs – The Bobs Special was constructed with so-called “regular” ribs (2-3/8” wide) that were ¼” thick instead of the normal 3/8”.  They create a light-weight canoe but are not as robust as the regular ribs.  You will probably encounter several broken ribs in your canoe restoration.

The edges of the ribs are chamfered in most Bobs Specials.  Replicate the angles found in your canoe.  Often, the edge closest to the centre of the canoe has tapered ends (11° chamfer) while the edge closest to one end of the canoe is chamfered about 25°.

Chestnut Canoe Planking

Planking – The planking in Chestnut Canoes was made of either Eastern White Cedar or Western Red Cedar.   Although the planks started out at 5/32” thick, you will probably be shaving replacement planks down to match the original planks.  Again, this results in a lighter, less robust canoe.  You will probably encounter many broken planks in your canoe.

???????????????????????????????

Seats – The seat frames are made of ¾” ash, oak or maple that is 1½” wide.  Both seats are suspended under the inwales with 10-24 carriage bolts and held in position with 5/8” hardwood dowel.  The rear stern seat dowels are 1¾” long while the front dowels are ¾” long.  All of the bow seat dowels are ¾” long.  The forward edge of the bow seat is about 51½” from the bow-end of the canoe while the forward edge of the stern seat is about 39½” from the stern-end of the canoe.

Chestnut Canoe Thwart

Centre Thwart – The thwart is made of ¾” ash that is 2½” wide.  It tapers from the centre to create handle grips on either side that are 2” wide.  They were attached directly under the inwales with galvanized steel 10-24 carriage bolts.  As with every component in the canoe, I seal the entire thwart with a couple of coats of spar varnish prior to installation and replace the original galvanized steel bolts with silicon bronze bolts.

mockup 02

All of this (and much more) is described in my book – This Old Canoe: How To Restore Your Wood Canvas Canoe.
If you live in Canada, CLICK HERE to buy the book.
If you live in the USA, CLICK HERE to buy the book.
If you live in the UK, CLICK HERE to buy the book.
Si vous habitez en France, CLIQUEZ ICI acheter le livre.

by Mike Elliott, Kettle River Canoes
email: artisan@canoeshop.ca

For those of you new to this blog and have not heard me on this topic before, let me be as clear as I can be: To anyone thinking about applying fiberglass to a wood-canvas canoe, I say, “DON’T DO IT!”  To anyone wanting to remove fiberglass from a wood-canvas canoe, the short answer is: HEAT.

Wood-canvas canoes are a product of a by-gone era; a time before planned obsolescence — when things were built with the long term interests of the consumer in mind.  The whole idea of building a canoe with wood and canvas was to have a vessel that lives and breathes.  These canoes work in the natural environment and are part of it.  They are held together with tacks and screws – no glue.  The wood flexes and moves with the water around it.  When part of the canoe breaks or rots, it can be repaired or replaced with comparative ease because it is designed to be taken apart.  As long as there are people who know how to restore canvas-covered canoes, they will live forever.

It has been about forty years since these canoes were the standard in the marketplace.  Not only has the technology of wooden canoe repair faded into obscurity, but the mindset of both manufacturers and consumers has also changed.  Synthetic materials are now generally seen as better – easier, tougher and longer lasting.  The consumer has been convinced that the new materials can improve that which is outdated or at least maintain it quickly and easily.

When it comes right down to it, wooden canoes and fiberglass just don’t mix.  Since the ribs and planking are held together with tacks, they flex and move naturally.  Over the years, the tacks tend to work loose and eventually have to be either re-clinched or replaced. Conversely, fiberglass resin is rigid.  Once applied, it tends to resist any movement.  The combination of a flexible hull and a rigid outside layer results in cracked or delaminated resin.  The tacks can also wear against the resin from the inside to the point where they come right through the resin.  It can take several months or several decades, but at some point the canoe needs to be repaired and the fiberglass has to come off.  It is then that the real problem with fiberglass on a wood canoe comes to light.  All of that synthetic resin has to be removed.  It is a long, painstaking process that usually has you cursing the person that put the stuff on in the first place. The moral of the story is: Avoid applying fiberglass to the hull of a wood-canvas canoe.  Learn how to re-canvas the canoe or find a professional to do it for you.

This leads us into the next question: How do you remove fiberglass from a wood-canvas canoe?  All you require is a professional-grade heat-gun, a 2” putty knife, a pair of pliers, safety equipment (work gloves, safety glasses and a respirator mask) and lots of patience.  The first step is to move the canoe into a well ventilated work space – preferably outdoors.  Then start at an edge of the canoe and apply heat to the resin.

At this point it is important to note that fiberglass resins come in two basic types – polyester and epoxy.  Polyester resins were the first to be developed.  If your canoe had fiberglass applied to it in the 1970’s or earlier, you can bet that polyester resins were used.  They tend to become brittle and deteriorate rapidly, so if the fiberglass on your canoe is delaminating it is most likely that you are dealing with a polyester resin.  Fortunately, this makes the removal of the fiberglass relatively quick and easy.  In many cases, the cloth can be ripped off by hand with very little need for heat.  When I say rip, please be gentle.  If you get carried away and pull at the fiberglass cloth too rapidly, you could end up tearing sizeable chunks of planking off the canoe as well (I speak from first-hand experience).

Epoxy resins hit the market in a big way in the 1980’s and are the standard today.  They are applied by first mixing a hardener with a resin in a two-part formula.  What results is a strong, tough plastic that bonds very well to wood.  Unfortunately, this means that the removal process is arduous and painstaking.

IMG_0600

As mentioned earlier, start at an edge of the canoe and apply heat to the resin.  If you are dealing with epoxy resin, you will probably have to apply the heat for several minutes before the cloth begins to respond to your attempts to lift it with the putty knife.  At some point, it does let go and the fiberglass cloth can be separated from the canoe.  Then move a few centimeters and continue the process.  Again, polyester resins let go fairly quickly.  You will find that large sheets of cloth come off in fairly short order.  I usually grab the cloth with a pair of pliers rather than with my hand.  Even with work gloves on, the pliers prevent nasty encounters with heat and/or sharp edges of fiberglass (again, this is the voice of experience talking).

IMG_0612

Once all of the fiberglass cloth is removed, return to the canoe hull with the heat gun and a putty knife.  Apply heat to any patches of resin still stuck to the wood.  Then, scrape the resin off.  Be prepared to settle into hours of tedious work.  It typically takes 15 to 20 hours to remove the fiberglass cloth and resin from a 16′ canoe.

Once you are back to the bare wood, the restoration is like that of any other wood-canvas canoe.  So, enjoy the pleasures of life in the slow lane, stay away from fiberglass and celebrate the fact that you have a wood-canvas canoe.

Many people complement me on the great fiberglass job on my canoes. They are shocked to learn that the canoes are covered with painted canvas.

Many people complement me on the great fiberglass job on my canoes. They are shocked to learn that the canoes are covered with painted canvas.

mockup 02

All of this (and much more) is described in my book – This Old Canoe: How To Restore Your Wood Canvas Canoe.
If you live in Canada, CLICK HERE to buy the book.
If you live in the USA, CLICK HERE to buy the book.
If you live in the UK, CLICK HERE to buy the book.
Si vous habitez en France, CLIQUEZ ICI acheter le livre.

If you have read the book, please post a review on Amazon and/or Goodreads and/or any other review site.